Yes, a vinyl fence can be installed on sloping ground. The proper way to accomplish this is to use a “stair-step” installation process. This means that each fence panel assembly section will be completely level between posts. To compensate for the slope, the posts in between the fence panels should step up or down in height accordingly. Using this method prevents any sagging and keeps the fence as level and structurally sound as possible.

The first step to installing vinyl fence post caps so they stay securely attached for the life of the fence is to prepare the surface for good adhesion before doing anything else. Be sure to wipe away all loose dirt or grime and allow the vinyl surface to dry fully. Using specially formulated vinyl fence glue, place a bead of the adhesive around the base of the post cap. Next, insert the post cap and hold firmly in place for about 30 seconds. By following this simple method, those vinyl fence post caps should remain securely seated even through the harshest elements.

In most cases. Yes. Quality vinyl fencing material is designed to stand up to just about anything mother nature can throw at it, short of being in the path of a “major” hurricane or tornado. Improvements in vinyl extrusion technology and the engineering processes of vinyl fencing systems over the years have come an incredibly long way since the initial days of vinyl fencing. Most vinyl fences are designed to withstand normal wind load. The amount of load is dependent on the installation of the posts and horizontal rails.

Mounting a vinyl fence post is just about the most difficult step of installing a vinyl fence. It’s also one of the most important – if the posts aren’t plumb and correctly measured, other problems will be created for the rest of the installation process. Most vinyl fence posts should be mounted with about a third of their length below the ground. A properly prepared post hole will be approximately one foot in diameter and have a gravel base of several inches. Once the hole has been prepared, quick-set concrete should be poured into the hole. While the concrete is still wet, place the post down to the footing. Make sure everything is plumb and level, and then secure the post so that it stays that way as the concrete sets. That’s about all there is to it! Also see digging vinyl fence post holes

• Discuss your plans with any neighbors whose property lies along your proposed fence line.
• Make sure your fence will be on your property.
• Check for easements in your deed. An easement is a right-of-way granted to another property owner or utility company which may limit the design and location of your fence.
• Confirm the location of underground utilities with local providers before you dig.
• Check local zoning laws which may regulate the size and placement of your fence. If you live in an historic district or a subdivision, check with your neighborhood association before proceeding with your plans.
• Contact your local building inspector to obtain the information you need for the depth, diameter and shape of your footings. Some codes may require that the bottom of a footing be wider than the top.
• Apply for the proper building permit as directed by local code.
• Pin-point the location of the corner, gate, and end posts. Notice ground strength conditions at all of these areas. Also notice how fast the ground dries up or retains water in areas of high traffic. Determine the direction you want the gates to open and mark these points with stakes or paint.
• Run a guide wire or string from stakes outlining the path of the fence. The height of the string should be the same height off the ground as the bottom of the bottom hole of the routed post when installed. Do not allow the string to touch the ground and without sagging.
• Lay a tape measure along side of the string starting at a corner post. Mark line posts every 8 feet on center with marking paint or stakes. Decide where short sections (any section less then 8 feet long) will be.

PVC Fence is the same as Vinyl Fence. PVC or Polyvinyl Chloride, is a vinyl compound which is formulated from raw materials that include PVC resin, UV inhibitors (TiO2), impact modifiers, stabilizers, and toners. As a building material, PVC is cheap, durable, and easy to assemble. In recent years, PVC has been replacing traditional building materials such as wood, concrete and clay in many areas.

Yes. Because there are no protruding nails, screws or other fasteners and because there are no splinters or sharp edges, vinyl fence is much safer than wood fence for children and pets.

The most common ingredient for vinyl fence is polyvinyl chloride which is modified to provide superior strength and ultraviolet resistance by including impact modifiers and ultraviolet inhibitors. The formulation was originally derived from that used for vinyl windows which has had a history of durability and structural integrity.